Analysis of Common Troubleshooting Methods for American Standard Dryers

The clothes dryer is a device that is used together with the washing machine. The American standard shrinkage washing machine is also equipped with the American standard Whirlpool dry washing machine, so it is inevitable that various failures and problems will occur during the use of the clothes dryer, affecting its use. As we all know, when the clothes dryer breaks down, it usually takes a certain time to report for repair, ranging from half a day to a week, which seriously affects family life and the progress of factory and laboratory use, Here, Standard Group has compiled some common faults and troubleshooting methods for clothes dryers for your simple reference.
Damaged dryer parts?
Drying part: 1. The heating tube is damaged; 2. The drying single (dual) temperature relay is damaged. Blowing part: 1. The connecting pipe of the air chamber heating chamber is damaged. The blower motor (fan blade) is damaged. Condensation part: The connecting pipe is damaged. The treatment is to replace the components.
"When the power is turned on, the power indicator does not light up, and the entire machine does not work."?
Firstly, check whether the mains voltage and power plug are normal. If the FR fuse is blown, find out the cause of the fuse. After troubleshooting, replace it with a 250V, 10A, 130 ℃ overtemperature fuse to eliminate the fault.
If the drying time exceeds 3 hours, the dried clothes will not be dried?
Check whether the dried clothes are too thick or not dehydrated, followed by whether the cloth cover zipper is open for air leakage. Upon inspection, the above points are normal, mostly due to the burning of one of the heaters PTC1 and PTC2. Use the resistance method to determine whether the resistance value is infinite, it will be broken. Replace with a new PTC, and the fault will be eliminated.
Sudden shutdown during the drying process (the fault phenomenon is WK action protection)?
The main reason is that there is a fault in the air supply circuit. It is necessary to check whether B, D1, D5, C, and M are damaged. It is usually caused by the abrasion of the electric brush during long-term operation of M, resulting in excessive temperature at the air outlet, and WR action. Replace M, or directly replace the motor from the old fan. Another reason is that there are foreign matters blocking the air inlet and outlet, which can cause this fault. After removing the foreign matters, the clothes dryer can operate normally.
Is there an explosion?
One of the common faults in the use of a dryer is the occurrence of a loud noise during the drying process. The reason for the explosion may be that the material inside the dryer is blocked, causing local temperatures to be too high, resulting in a fire inside the equipment. The solution to this problem is to immediately shut down the machine for cleaning and reduce the fuel supply to reduce local temperatures.
Unable to discharge finished material?
During the use of dryers, there may be situations in the seed industry where the installation of dryers is not standardized, resulting in air leakage from internal pipes, low wind pressure, and inability to properly discharge the dried products. The solution at this point is to check the installation drawings to see if each component is correctly installed. If the failure cannot be eliminated, you can simply re hide the dryer.
Uneven drying and wetting of drying materials?
During the use of the dryer, uneven drying humidity of materials may also occur. This situation is generally caused by uneven heating due to the solidification of materials into agglomerates. Therefore, it is necessary to ensure that the materials are dispersed before pouring into the drying raw materials, and pay attention to the correct use of the dryer to ensure that the materials are stirred and heated evenly.
Abnormal discharge of separator stack?
During the use of the dryer, there will also be chimney discharge phenomena due to inappropriate or too small separators, or unreasonable design, and inaccurate calculation of the wind pressure of the air network. The solution at this time is to promptly inspect, replace, and modify the separator, and repair and handle abnormal components.

The above content is organized by Superb heater Company, super heater. Mainly professional production: industrial heating elements, temperature measuring elements, production equipment, accessories, and raw materials such as tubular heaters, tubular heaters, belt heaters, ceramic heaters, silicone rubber heaters, thermocouples, etc.

Welcome global industry partners to discuss cooperation!