1700℃ Laboratory Heat Treatment Ceramic Fiber Muffle Furnace with Exhaust Holes
Leave a message
The core advantage of the 1700°C (1700°C) laboratory heat treatment ceramic fiber muffle furnace with vents lies in the synergy between its precise temperature control system and innovative exhaust design. When the furnace reaches ultra-high temperatures, a built-in PID intelligent control module monitors the thermal field distribution in real time. Dynamic compensation using 16 sets of silicon-molybdenum rod heating elements keeps temperature fluctuations within ±1.5°C. This stability is particularly important for annealing semiconductor materials-for example, when processing silicon carbide wafers, where sudden temperature fluctuations can lead to an exponential increase in lattice defects.
The exhaust holes utilize a stepped honeycomb structure, symmetrically distributed at 45-degree angles on both sides of the furnace. This layout not only ensures efficient exhaust gas discharge but also creates a protective air curtain through airflow guidance. Experiments have shown that when fed with 99.99% pure nitrogen, the oxygen content in the furnace can be maintained below 5 ppm, perfectly meeting the sintering requirements of titanium alloy powders. The upgrade to the ceramic fiber module is noteworthy. The new generation of ZrO2-reinforced fiberboard maintains a linear shrinkage of 0.05% even under repeated thermal shock. Its multi-layer composite structure acts as a "thermal shield" for the furnace, keeping the outer wall temperature consistently below 60°C.
The innovative user interface is equally impressive. The 7-inch touchscreen integrates 200 process recipe storage functions. Researchers simply call up a preset program, and the system automatically completes a temperature ramp from room temperature to 1700°C. A specially developed rapid cooling mode can reduce the furnace temperature to below 800°C in just 90 seconds, demonstrating its unique value in rapid quenching experiments. Regarding safety, a triple interlock system (temperature sensor, air pressure monitoring, and access control system) forms a closed-loop protection loop. Any abnormality detected immediately shuts off the power supply and triggers an audible and visual alarm.
The 1700°C laboratory heat treatment ceramic fiber muffle furnace with exhaust port is a high-temperature device commonly used in laboratories of universities, research institutes, and industrial and mining enterprises. It is primarily used for high-temperature sintering and heat treatment experiments. The following is a detailed introduction:
Structural Features:
Furnace Chamber Material: High-purity alumina fiber is typically used. This material offers advantages such as high-temperature resistance, excellent thermal insulation, strong thermal shock resistance, high chemical stability, and light weight. Some furnace chamber surfaces are also coated with imported high-temperature alumina to improve heating efficiency and service life.
Heating Elements: Silicon-molybdenum rods are generally used as heating elements. When energized, the silicon-molybdenum rods generate heat due to their inherent resistance, which radiates heat into the furnace chamber, raising the furnace temperature to 1700°C. Heating elements are evenly distributed around the furnace chamber to ensure uniform temperature distribution.
Exhaust Hole Design: Air inlets and outlets are located at the rear and top of the furnace, respectively, allowing inert gas to enter the chamber to remove undesirable contaminants and moisture, extending the service life of the heating elements and furnace chamber. The air inlet is typically a small-diameter pagoda-shaped nozzle, while the air outlet is relatively large.
Shell Structure: A double-layer shell structure with an air- or water-cooled interlayer effectively reduces the shell surface temperature, preventing operator burns and minimizing heat loss.
Performance Parameters:
High Temperature: The maximum operating temperature can reach 1700°C, but a long-term operating temperature of 1600°C is generally recommended to extend the life of the equipment.
Temperature Control Accuracy: PID programmable temperature control is typically used, with an accuracy of ±1°C, enabling precise control of experimental temperatures.
Heating Rate: The recommended heating rate varies across different temperature ranges, such as ≤10°C/min (≤1400°C) and ≤5°C/min (1400-1600°C). Due to the low heat capacity of ceramic fiber materials, some products offer faster heating rates, reaching 1000°C from room temperature in as little as 30 minutes.
Safety Protection:
Overheat Protection: When the furnace temperature exceeds the set upper limit, the system automatically shuts off the power and issues an audible and visual alarm.
Burnout Protection: If the thermocouple fails or becomes disconnected, the temperature control system immediately stops heating to prevent temperature runaway.
Door-Open Power-Off Protection: Some muffle furnaces are designed with a door-open power-off feature. When the furnace door is opened while at high temperatures, an alarm sounds and the heating power is cut off, ensuring operator safety.
Other Protections: Overload, overcurrent, overvoltage protection, and a grounding device are also provided to prevent damage from electrical faults, ensuring the safety of both equipment and operators.
Applications: Primarily used for powder sintering, ceramic sintering, high-temperature testing, and quality inspection, such as analyzing the oxide content of chemical raw materials, sintering zirconia, and sintering nanomaterials. It can also be used for gradient sintering of coatings for aircraft engine turbine blades.
At the forefront of materials science, this equipment's modular design demonstrates strong adaptability. By configuring an optional vacuum flange interface or atmosphere control system, it can easily switch to low-pressure chemical vapor deposition or controlled atmosphere sintering modes. When a research institute recently used it to conduct graphene doping experiments, the specially designed quartz observation window could also be used with a high-speed camera to record the material phase change process, providing a new observation dimension for high-temperature reaction kinetics research.








