Chemical Resistant Ptfe Acid Resistance Immersion Heater Element For Corrosive Fluid

The tetrafluoroethylene heating tube is a new type of electric heater with strong corrosion resistance. It is used for heating and anticorrosive heating pipes of various corrosive liquids. It has excellent aging resistance and good winding performance, and adopts low surface load design. The connector adopts totally enclosed anti-corrosion acid-base, non heating section and overheating safety protection system, which are completely customized according to the customer's requirements. It ensures that the heater is not easy to burn, has a long service life, is fully sealed, does not corrode and does not leak electricity safely and reliably. Applicable temperature is below 110C. The anticorrosive heating pipe has excellent corrosion resistance: F4 is a chemical inert material, which can work in all media except Fluorine, molten alkali metal, chlorine trifluoride, uranium hexafluoride and Perfluoroethane under high temperature. Such as: all kinds of strong acids and bases, sulfuric acid, hydrochloric acid, nitric acid, hydrofluoric acid, sodium hypochlorite, naphthalene, benzene,,, aqua regia, chlorine, toluene, various organic solvents, etc.

 

L-shaped PTFE heating pipe:

1. The PTFE electric heater adopts the high-quality stainless steel electric heating tube inner core, and the outer PTFE tube (PTFE) has strong corrosion resistance, which is suitable for all kinds of corrosive liquid heating. 2. The electric heater adopts low surface power design (1.5w/cm2) to ensure the service life of the product. 3. Attention shall be paid to the installation position of the electric heater to prevent the solid in the solution from depositing on the surface of the electric heater, or if the liquid is too pure or too low, the iron fluorine (PTFE) will be burned due to poor surface heat dissipation. 4. The size of electric heater shall not be arbitrarily reduced, and the surface area shall not be reduced, otherwise the surface power of electric heater will be too large, which will affect the service life of electric heater. 5. All electric heaters can be equipped with over temperature protection or PT-100 temperature sensing probe to ensure the product service life and complete equipment. 6. The connector adopts totally enclosed anti acid and alkali, non heating section and overheating safety protection system, which are completely customized according to the customer's requirements.

Spiral PTFE heating tube:It is suitable for various corrosive liquid heating equipment, such as electroplating, electrolysis, degreasing, pickling, electroless nickel phosphorus, anodizing, aluminum berthing, smelting, chemical industry, medicine, etc.

Products Description

Heat intensity	Not exceeding 30w/cm2 (advisable)
Exhaust extreme (when cold)	<=0.1mA to 242 v.
Insulation (when cold)	5 Min Ohms 500 Watts minimum
Dielectric strength	1500v. 1/sec
Working temperature	1050 Deg C max.
Length tolerance	+/-1.5%
Diameter tolerance	-0.02 to -0.06 mm
Cut off connection tolerance	+/-15 mm
Power tolerance (w)	-0.05
Wattage Tolerance	+5%, -10%
Resistance tolerance	+10%, -5%
Tube diameter	Φ8.5mm-Φ22mm
Tube Material	Spray fluoroplastics, fluoroplastics sleeve, titanium
Voltage and power	customized
Warranty	one year

 

Features:

1. Select high-quality stainless steel (SUS316 or SUS304) electric heating tube inner core and outer PTFE tube (PTFE) to make, with strong corrosion resistance, suitable for heating various corrosive liquids. 2. Attention shall be paid to the installation position of the electric heater to prevent the solid in the solution from depositing on the surface of the electric heater, or if the liquid is too thick and the liquid level is too low, the PTFE tube (PTFE) will be burned due to the poor heat dissipation on the surface. 3. The shape is divided into vertical and bottom heated "L", "1", "circle", "m" and so on.

Instructions：

1. It has strong chemical corrosion resistance and can be used for heating highly destructive liquid. 2. The heating pipe in the PTFE electric heater is made of special metal and coated with PFA. 3. Any PTFE electric heater can be adapted to PT100, temperature fuse and temperature switch. 4. It can be made according to customers' requirements. Our existing combined type, spiral type and L-type circle type are available for reference. 5. It is not allowed to touch, touch or scratch the surface of PTFE tube during use.

The commonly used PTFE heating tube is a new type of strong corrosion-resistant electric heater made of PTFE sleeve, which is used for heating various corrosive liquids. It has excellent aging resistance and good winding performance, and adopts low surface load design. The PTFE heating pipe can be divided into two types: one is to spray the surface of the heating pipe with fluoroplastics directly, the other is to cover the outer layer of the iron heating pipe and the copper heating pipe with fluoroplastics casing.

1.Safety protection system against acid and alkali, cold end and overheating.

2.The anti-corrosion heating pipe is made of high-quality stainless steel electric heating pipe inner core and outer PTFE pipe. It has strong corrosion resistance and is suitable for all kinds of corrosive liquid heating.

3.High temperature resistance,insulation,antiinterference.

4.The anti-corrosion heating pipe is designed with low surface power to ensure the service life of the product. All anti-corrosion heating pipes can be equipped with over temperature protection or PT-100 temperature sensing probe to ensure the product service life and design safety. 

 

Applications

PTFE heater is the best choice for heating, condensing, evaporating and condensing corrosive liquid such as electroplating, electrolysis, degreasing, pickling, electroless nickel plating, phosphorus plating, hydrofluoric acid, anodized aluminum, smelting, chemical industry, medicine, food, etc.

FAQ

 

 

Q1:who are we?

We are based in Shenzhen city, China, founded in 2016, sell to North America(25.00%),Domestic Market(17.00%),South America(15.00%),Western Europe(5.00%),Eastern Europe(5.00%),Southern Europe(5.00%),Oceania(5.00%),Central America(5.00%),Northern Europe(5.00%),Africa(3.00%),Eastern Asia(2.50%),South Asia(2.50%),Mid East(2.50%),Southeast Asia(2.50%). Our team is total about 11-50 people in our office.

 

Q2: how can we guarantee quality?

A: Always a pre-production sample before mass production;

Always final Inspection before shipment;

 

Q3: what can you buy from us?

A: thermocouple,Temperature sensor,Cooking thermometer,Bimetal thermometer,temperature controller

Q4: what services can we provide?

A: Accepted Delivery Terms: FOB,CFR,CIF,EXW,FAS,CIP,FCA,CPT,DEQ,DDP,DDU,Express Delivery,DAF,DES；

Accepted Payment Currency:USD,EUR,JPY,CAD,AUD,HKD,GBP,CNY,CHF;

Accepted Payment Type: T/T,L/C,D/P D/A,MoneyGram,Credit Card,PayPal,Western Union,Cash,Escrow;

Language :English,Chinese,Spanish,Japanese,Portuguese,German,Arabic

French,Russian,Korean,Hindi,Italian

FAQ2

Q5: What is the lead time for heat products?

A: Samples - within 3 working days with materials in stock Mass production - usually 7-14 days (depends on quantity and raw material situation, please further discuss with our team. )

Q6: What is the MOQ for heat products?

A: heat products produced with common materials can be ordered at 1pcs. If infrequently used materials required, it depends on the situation of the materials.

Q7: Do you manufacture custom parts?

A: Yes. We have thousands of designs in our profile of custom heaters and sensors designed for every imaginable application. Our Sales and Engineering teams are here to help you design a product that fits your needs.

Q8: If we have heating projects, how to progress project design or select a product?

A: We have professional sales to provide pre-sale consulting services and engineering team for technical support. Any questions about products or technical questions please contact our sales team and provide specific applications and requirements.