Maintenance of Electric Fry Pot Common Faults of Electric Hot Pot

Common troubleshooting methods for electric fryers

The lamp of the multifunctional electric pot does not light up and does not heat up

(1) Check if the power cord is powered on.

(2) The switch light is broken, replace the switch light (open the back cover, disconnect the light connection, and replace with a new light).

(3) The temperature controller contacts are burnt out, replace the temperature controller.

(4) The heating tube is burnt out, replace it with a new pot.

The multifunctional electric pot heats and stops at one time

(1) The thermostat is malfunctioning, replace it.

(2) Detach and replace with a new pot.

Whether the multifunctional electric pot's rice cooking button light is on or not does not affect its use. If the rice is not cooked well, check the rice cooking temperature controller inside the pot.

Leakage fault of multifunctional electric pot

(1) Are there any loose wires inside the pot.

(2) Is there a magnetic pad at the connection between the electric heating tube and the wire.

(3) Whether the temperature controller and other charged electrical components have touched the pot body.

(4) Is the electric heating tube leaking electricity? If the electric heating tube leaks electricity, it can only be replaced with a new pot.

(5) Is there a grounding wire for the socket used.

(6) Water ingress or dampness.

(7) Do not use the light on the electric pen to determine if there is a leakage.

The plastic parts (plastic base, pot ears, etc.) of the multifunctional electric pot are broken. First, remove the parts from the new pot, replace them yourself, and then replace them with new ones.

Common faults and maintenance of electric hot pot

Fault 1: Not hot

Reason: 1. The power cord is disconnected. 2. Poor contact between plugs and sockets. 3. The electric heating wire is broken.

Troubleshooting: 1. Identify the disconnection point of the power cord, wrap it with insulating tape, and if necessary, replace it with a new wire of the same specification. 2. Replace the socket and eliminate poor contact. 3. Replace the electric heating wire with a new one.

Fault 2: Leakage

Reason: 1. Insulation damage, such as damage to the outer skin of the wire. 2. The electric heating wire comes off the slot and collides with the outer shell.

Troubleshooting: 1. Repair the damaged insulation by wrapping it with insulation tape or replacing it with a new one. 2. Carefully remove the electric heating wire holder, press the detached electric heating wire into the slot, and prevent the electric heating wire from falling out of the slot again.

Fault 3: Burn out of electric heating element

Reason: 1. The wire ends of the power cord collide with the plugs at both ends. 2. There are conductive foreign objects and burnt marks at the electric socket. 3. There is a short circuit in the wiring inside the base. 4. Internal water ingress into plugs, sockets, or bases.

Troubleshooting: 1. Identify where the wire ends collide and separate them. 2. Remove foreign objects and burnt marks from the electric heating socket. 3. Open the base to identify the short circuit point and eliminate it. 4. Wipe off water and dirt with a dry cloth.

Precautions for using electric hot pot:

1. The power of electric hotpot is generally high, and the sockets and power cords used should match the power consumption to avoid accidents.

2. The electric hot pot uses a single three core textile flexible wire as the power lead. When connecting, first insert the plug of the power lead with a socket into the electric heating socket of the pot body, and then place the switch of the constant temperature device in the middle or appropriate position. Usually, it is placed in a high temperature range at the beginning, and after the water boils, it can be placed in an insulation range. Be sure to have good grounding.

3. For non constant temperature electric hotpot, do not dry burn the heating element and pot body. When it is necessary to remove water from the pot, the power should be cut off and cooled slightly before releasing the soup from the pot. This can prevent the waste heat from the porcelain plate at the bottom of the pot from burning the bottom of the pot.

4. When using, do not touch the electric hot pot with wet hands, and do not touch the hot pot with one hand and the faucet with the other hand to prevent electric leakage and injury to people.

5. It is important to regularly maintain the cleanliness and hygiene of electric hotpot. After each use, the power should be cut off and the hotpot should be cleaned. During cleaning, attention should be paid not to let water seep into the pot body. It is best to use a dry cloth to wipe off areas such as electric sockets that have oil stains and debris. The surface of the pot should also be wiped economically to maintain cleanliness and prevent oxidation.

6. After the pot body of the electric hot pot has copper rust, continuing to use it may cause food poisoning. You can use a cloth dipped in vinegar and then add some salt to wipe the pot body with copper rust, which can clear it