Triple Tubes Metal Electric Immersion Heater

Product Detail

metal heaters are designed for the demands of corrosive chemical heating, with a vast array of configurations available, such as open tank, screw plug and flange. We offer sizes of metal heater as small as 500 watts for laboratory environments and as large as 36,000 watts for industrial applications.

 

Standard and custom configurations for over-the-side and bottom installations in open tanks. Thermal overtemperature protection standard (except screw plug), and our metal heaters have certified by CE and ISO9001:2008.

 

Product Descriptions:

1. The metal heaters are made of seamless tubes of sus304, sus316 or titanium, three elements of diameter 50mm, in vertical shape.

 

2. Power of the metal heaters is designed according to the installation location, liquid chemical propoties and the deposition of the solid contents in liquid.

 

3. Hot-zone length of the metal heaters depends on its watts; different watts, different hot-zone length. And the cold-zone length is flexible, it should be designed according to customers' equipment requests.

 

4. For safety design principle, the hot-zone of the metal heaters should be at least 100mm below the chemical liquid level.

 

5. With voltage of 110V/P, 220V/P, 380V/P, 220V/3P, 380V/3P, 415V/3P, 480V/3P and power range from 0.5kw to 36kw.

 

6. All metal heaters are matched with overheat protection switch or heat detector.

 

7. All metal heaters reach the international standard of CE certification, which insure the reliability and service life.

 

 

 

Types of immersion heaters

Explosion-Proof Flanged Immersion Heaters

Commonly used in refinery and petrochemical markets, Indeeco explosion-proof flanged immersion heaters are an ideal solution for heating tanks, pressure vessels, and in-line heating.

 

Explosion-Proof Screw Plug Immersion Heaters

Indeeco explosion-proof screw plug immersion heaters are CSA approved, for use in hazardous areas classified as Class I, Division 1, Groups B, C and D; and Class II, Division 1, Groups E, F and G.

 

Non-Hazardous Flanged Immersion Heaters

Indeeco flanged immersion heaters are one of the most widely used solutions for heating fluids and gases. Designed for use in tanks, pressure vessels, and in-line heating, flange heaters are easy to install and maintain.

 

Over-the-Side Heaters

Indeeco Over-the-Side heaters are designed to provide the maximum in application flexibility and to minimize installation cost. They are ideal for jobs where easy installation and quick replacement or cleaning must be accomplished without emptying the tank.

 

Rectangular Flange Heaters

Large Diameter Elements provide extra electrical insulation for superior dielectric strength. Element insulation is compacted to insure uniform heat transfer from coil to sheath and all bends are repressed to insure insulation integrity in this critical area. Special sheath materials and alternate flange designs are available for special needs.

 

Replacement Boiler Flange Heaters

These 4-7/8" flange heaters are three-element modules specifically designed for large steam or hot water boilers. They offer a simple, practical solution to two problems inherent in all electric boiler designs: element stocking and field replacement.

 

Screw Plug Immersion Heaters

Indeeco screw plug immersion heaters are ideal for use in direct heating of liquids and gases in a variety of processes for hazardous and non-hazardous locations. Indeeco offers customized wattages with voltages up to 600V and are available in 1″, 1-1/4″, 2″, 2-1/2″, and 3″ NPT sizes. You can order from stock or customize for your specific application.

 

Tank and Basin Heaters

Indeeco Tank Heaters are used to maintain or raise the temperature of gases and fluids in tanks from -300°F to 1000°F for a variety of applications and industries. These heaters are designed with low watt density, open coil heating elements for uniform heating of even the most temperature sensitive materials.

 

Bottom-Mounted Immersion Heaters

Bottom-Mounted immersion heaters were originally designed for use in coffee urns. However, their compact construction makes them ideal for use in steam tables, humidifiers, sterilizers and other applications requiring a very low heater profile and a short element length.